Ghost Immobiliser Fitter
Ghost immobilisers are among the most effective ways to protect your vehicle from theft. They prevent vehicles from starting unless the proper pin code is entered. They can be used to track vehicles remotely. ghost immobiliser reviews are getting more and more popular and a lot of insurance companies offer discounts to drivers with these systems installed.
It is tamper-proof.
The Ghost Immobiliser is a sophisticated security device that blocks your vehicle from starting unless a unique PIN code is entered or a beacon is visible. The system can be modified to fit your vehicle and is highly efficient as an anti-theft device. It is essential to test your system following installation to ensure it is functioning properly. By entering the PIN as you start the engine is a straightforward method to verify that the system has been installed correctly. Regular testing will help to identify any problems or issues that may be affecting the system earlier.
The system communicates with the ECU to stop your car from running unless the proper sequence is entered. This can be done by using the electronic buttons on your steering wheel or via an app for smartphones. Its tamper-proof design as well as its low profile makes it difficult for thieves to find or remove. It can be used combination with a beacon for keeping track of the location of your vehicle. It's a great method to safeguard vehicles that have been modified or vehicles that are expensive or have a limited supply.
This tamper-proof device makes use of the buttons on your steering wheel to generate an exclusive sequence that only you can identify. The sequence is mathematically impossible for thieves to guess and can be easily altered by using a reset code. It is easily installed by a technician in the majority of vehicles.
After you have installed the device, you will need to connect it an electrical source as well as a grounding point. To identify the wires that are required to connect the device, obtain the wiring diagram of your vehicle. To prevent short circuits or electrical damage, insulate all connections with heat-shrink tubing or insulation. Check the mounting of the device as well as its connections to make sure there isn't any indication of altering the connections.
Ghost 2 can be set up in Service/Valet mode for older vehicles that require battery isolation during servicing or maintenance. This will disable the device using a unique pin code. This will stop it from being turned off again by thieves.
Wireless
In contrast to other anti-theft devices ghost immobilisers function in a silent manner and are not able to be detected by thieves. They can be fitted in a variety of vehicles and shield them from key cloning, hacking and signal relay attacks. They also connect to the CAN network and are used to monitor a vehicle remotely. They can provide owners with instant notifications when their vehicle is stolen. This is among the most effective methods to protect your car from theft and some insurance companies offer discounts to customers who have these devices installed.
The Ghost II immobiliser offers a easy and affordable method to safeguard your car from theft. This device is wireless and compatible with most vehicles. It is weatherproof, tamperproof and compatible with all vehicles. It also comes with a 3-year warranty. The Ghost II is unlike other security products in that it does not require additional wiring or other components. Its unique pin code sequence guards your car from key cloning and theft by blocking the engine from starting unless a special disarm sequence is entered. This sequence could range between one and 20 buttons, meaning that thieves will have to spend much more time trying to crack the code before they are able to drive away.
Another benefit of the Ghost II is its ability to block signals from a burglar's key fob. It can determine if a key fob is duplicated or stolen and disable the engine by activating an alarm. It can also prevent the use of a signal relay device, which is commonly used by organized car-thief gangs to gain entry to vehicles.
It is crucial to test the Ghost Immobiliser system to ensure that it's working properly. This will help you spot any issues early and address them before they become serious. As part of your routine check-up of your vehicle, it's recommended to test the system. Enter the PIN code into the system and then start the engine.
It is crucial to put the immobiliser unit in a secure area in order to make it difficult for thieves to access. If you can, hide the unit behind the dash by using cable ties. Also, ensure that all connections are insulated and not exposed to potential manipulation by thieves. You should also verify the location of the mounting to ensure that it is safe.
It can be used with many vehicles
The ghost immobiliser is a very effective security device to protect your car from theft. It prevents the engine of your vehicle from running until the correct pin code is entered. The code can be generated by pressing the buttons on the steering wheel, door panel or centre console. The immobiliser is secure and can be reprogrammed by the owner at anytime. It also protects against key-cloning and hacking.
While some drivers might try to install the Ghost Immobiliser themselves but it is recommended you hire an expert. This is because the process of installation is complex, and errors could cause the device to be ineffective or even cause damage to your vehicle. DIY installation can also invalidate the warranties of the Ghost Immobiliser, as well as your vehicle.
A good place to start is to get the wiring diagram of your vehicle model. This will provide an overview of the CAN H wires and CANL wires that are used to power the immobiliser. Once you've located these wires, mark them to ensure that they're not accidentally disconnected during the installation process. Also, be sure to choose a safe and reliable grounding point for your system.
It is a good idea to test the immobiliser after the wires are connected to ensure that everything is functioning properly. Then, enter the PIN code to start the engine and check if it is able to start properly. It is also a good idea to test the immobiliser on a regular basis to ensure that it is working in the way it was intended to.
Another benefit of the ghost immobiliser is that it does not require any key fobs or LED indicators, and can be disarmed by entering a unique sequence of buttons on your steering wheel, door panel, or centre console. The immobiliser also leaves no trace of its location, making it difficult for thieves to detect. Additionally, it can be used to enhance the security of your vehicle in the event of a break-in and is recommended by a variety of insurance companies.
Easy to install
The Ghost immobiliser is an advanced device that keeps your vehicle secure from the most skilled thieves. It prevents your vehicle from starting until a specific PIN or sequence is entered with the key fob. This prevents hacking, cloning and even key theft, meaning that thieves cannot steal your car. It also makes use of a variety of other sensors that detect attempts to drive away, and can notify the owner or the police in event of tampering.
Installing a Ghost Immobiliser can be difficult, especially for those who haven't installed alarms or security systems prior to. Utilizing the right tools and materials is crucial to a successful installation. A multimeter is a great tool to check electrical values, and insulation tape and cable ties can protect connections. The user's manual for the Ghost immobiliser provides specific guidance tailored to your vehicle's model and wiring.
It's important to check the locations of the wires for the CAN H and L before the installation to ensure precision. They are crucial for powering the immobiliser. Errors could lead to an ineffective system or even failure. Mark the wires using labels or tape so that you can keep track of them. You should also identify the source of constant 12V and a grounding.
Once you've found the proper location, you're now ready to start assembling the ghost immobiliser. To avoid short circuits or a mistaken airbag deployment, you'll need to shut off your battery first. Then you can start connecting the wires. Follow the directions in the manual to ensure that the installation is clean and secure.
After you've completed the wiring, connect the Ghost immobiliser via CAN to the engine control unit. This makes it very difficult for thieves to remove or disable the device because it's directly connected the control unit. It is also tamper proof, and the only method to disable it by entering the pin code is to enter a personal one. The pin code is only known to the car's owner and the installer.
You can also use Ghost immobiliser to temporarily permit another person to drive the car, for example when you're away on business or need service. This feature is known as the Service/Valet Mode and it can be turned on using a key fob or mobile app.